Concrete floor installation in Arlington WA - a surface finished and cured to wear well
Old floor dusting, cracking in odd places or rocking under your shelves? We pour, finish, joint and cure a new one that wears evenly.
Concrete floor installation in Arlington, WA is more than the pour. We place the concrete, then finish, joint and cure it into the surface you'll walk and work on. Most calls start with an old floor that dusts, cracks in odd places or has high and low spots, and that often comes from finishing and curing done at the wrong time.
The price moves with the floor's size, whether it needs rebar, the steel bars that help hold a slab together, a moisture barrier for a covering, and any stain or stamping. The schedule turns on the prep and the cure. We're based in Arlington and work the cities around it, from Everett up into the Skagit Valley and out to Camano. Your written estimate gives the figure for your floor.
What our concrete floor installation covers
- Finishing and curing on time. We schedule the finishing, the joint cuts and the curing, which is the wait while concrete hardens, because that timing decides whether a floor wears well or dusts and scales.
- Joint layout shown up front. Control joints are shallow cuts that give the slab a straight place to crack, and I mark where ours will go so you see the plan before the pour.
- Moisture barrier before a covering. If tile, wood or a coating is going on top, we settle the barrier with you first, since the industry's floor guide finds one right against the slab protects coverings best.
- Licensed and insured in Washington. We're fully licensed and insured. The state requires construction contractors to register with Labor & Industries, and you can look any contractor up there before you hire.
- The owner looks at your job. I'm the one who comes out to look at the floor. Our crew and I have done the work since 2023, and we bring in an engineer when a job calls for one.
What goes wrong with concrete floors
| Problem | What it looks like | Usual fix |
|---|---|---|
| Cracks in random places | What it looks like: Cracks wandering across the floor instead of following straight lines | Usual fix: New floor with control joints cut on schedule |
| Dusting or scaling | What it looks like: Gray powder on everything, or thin flakes peeling off the top | Usual fix: Replace it, with finishing and curing timed right |
| High and low spots | What it looks like: Shelves rock, carts drift and a straightedge shows gaps underneath | Usual fix: Replace the bad section or pour a new floor |
| Covering coming loose | What it looks like: Tile popping, flooring cupping or a coating bubbling over the slab | Usual fix: New slab with the moisture barrier planned with you |
Repair the floor or pour new
- Fill the cracks. When the floor is flat and sound with only a few cracks, filling them is the cheaper answer, and I'll tell you so instead of selling you a new floor.
- Replace a section. When one area is broken up or sits low, we saw it out and pour a new piece, so the sound floor around it stays where it is.
- Pour a new floor. When the top dusts or scales all over, or a covering is going down that needs a barrier underneath, a full new floor is the better place to spend.
How we plan and pour your floor
- Call or send the form. Call (360) 474-2804 or use the form, and tell us the floor's size, where it goes and what covering you plan to put on it.
- I look over the site. I measure and ask how you'll use the floor, because a shop that takes rolling loads gets planned differently from a basement under carpet.
- Written estimate. You get a written estimate that says plainly what's in it and what isn't, so nothing about the job is left to guess later.
- Plan before the pour. We settle the layout, the prep, where the joints go and, if a covering is coming, where the moisture barrier sits.
- Pour, cure and walk-through. Our crew pours, finishes and cures the floor while your household stays clear, since wet concrete can cause chemical burns and eye damage, then we walk it with you.
Keeping a new concrete floor sound for years
A floor holds up best when it gets its full cure before heavy use and its cracks land in the joints. Clean up oil and chemical spills, and if a crack strays outside a joint line, call and ask us about it.
We pour floors for homeowners and small business owners in Arlington and nearby, from Marysville to Stanwood, and the same crew builds concrete steps and pool decks when the work runs past the floor. Call or send the form to ask for a free estimate.
Tell us about your floor
Send the floor's size, where it goes and any covering you plan. We reply within one business day and set a time for me to come out.
(360) 474-2804- Free on-site estimate
- What's in and what isn't
- No pressure to book
Concrete floor questions we hear
What does a concrete floor cost near Arlington, WA?
A concrete slab or pad in Everett usually costs about $7 to $14 per square foot. That's a nearby market reference for the slab itself, not our price. After I measure, the written estimate shows the figure for your floor.
Will my new concrete floor crack?
It will probably get a few small cracks, because even a well designed and well built floor does. Joints in the right places keep those cracks small and in lines we picked, so plan for controlled hairlines rather than none at all.
How soon can we walk on a new concrete floor?
A new slab should be walkable within 48 hours, heavier loads are best kept off for a week, and full cure takes about a month. Plan moving back in and bringing in shelving, vehicles or equipment around that, and ask us if you're unsure what counts as heavy.
Who issues building permits for a concrete floor in Arlington, WA?
Arlington's Building Services Division issues the permits state and local codes require. Its list names homes, additions and accessory structures, not floors, so ask the city's Community & Economic Development team, who meet with owners about planned projects at ced@arlingtonwa.gov or 360-403-3551. We check before scheduling and tell you what we'll file and what falls to you.